新聞中心
NEWS CENTER
聯系我們
CONTACTS US
濟南皓暉建材有限公司，總部位于中國泉城——山東濟南，是一家專業生產銷售石塑電梯門套，仿大理石電梯門套的專業廠家。皓暉建材在電梯門套生產行業很多年，憑著優質的產品質量和完善的售后服務，在全國各地都有我們的工程案例。
我們本著“以質量求生存 ，靠管理出效益，憑信譽贏口碑,以實干筑輝煌”的經營理念，公司將立足于當代建材現代化發展前沿，依靠科技、勇于探索，以優質產品優良服務、信譽與廣大用戶攜手共創輝煌。
聯系電話： 15853163650
工廠地址：山東濟南章丘區（歡迎廣大客戶來廠勘察）
公司動態
COMPANY NEWS
講解一下電梯門套施工注意事項
2017-01-20 18:17:12 文章來源：tongma800.com
講解一下電梯門套施工注意事項，下面小編為您講解一下：
Explain the construction elevator door notices, the following small for you to explain:
1.在安裝電梯門套時，想要將各層需要的石材挑選好。根據尺寸、顏色和花紋來搭配，然后搬運到各個樓層需要使用的地方。
1 in the elevator door installation, to each layer of stone selection. According to size, color and pattern to match, and then transported to the floor where the need to use.
2.在安裝時要注意石材的紋理，盡量保持色澤一致，紋理連貫。安裝完成之后，電梯門套的美觀性才會最佳。
2 in the installation should pay attention to the texture of the stone, as far as possible to maintain consistent color, texture coherence. After the installation is complete, the appearance of the elevator door will be the best.
3.彈線的時候要仔細測量，不僅一個門套要做好垂直和平整性，每個門套之間也要注意這些問題。
When the 3 bomb line must be measured carefully, not only a door to do vertical integration of peace, we should pay attention to these problems between each.
4.在安裝側板和線條時，要保證至少有2個掛件作為支撐件。安裝角鋼的位置要測量精確，在中間增加一個加固點的點位。這樣做是為了讓門套石材更加穩定、牢固。
4 in the installation side and lines, to ensure that at least 2 pendant as support. The installation angle of the position to increase the measurement accuracy, a reinforcement point in the middle. This is done in order to make more stable and solid stone door.
5.安裝電梯門套時不要靠得太緊，在電梯門框邊預留5mm到8mm的位置，注意讓四周的預留位保持一致。
5 when the elevator installation door and don't get too tight in the elevator door post reserved for the 5mm to the 8mm position, pay attention to the surrounding the reservation is consistent.
6.在安裝電梯門的檻石時，地磚和電梯框邊要有3mm左右的坡度，門框邊和頂面石材外口要有2mm左右的斜度。
6 in the installation of the elevator door sill stone, floor tiles and lift frame edge is about 3mm to slope, and the top surface of the doorframe side stone mouth about 2mm slope.
7.頂面線條碰和側面線條的角度為45°，碰角做到嚴密、平整，施工時注意縫隙內不留余膠。如果有余膠就及時清理掉，然后使用勾縫劑處理。線條大小一致，造型穩合整體風格。
7 the top surface of the line and the side of the line angle of 45 degrees, the impact angle to be tight, smooth, pay attention to the construction of the gap does not leave any glue. If you have time to clean out the glue, and then use the pointing agent. The size of the same line, the shape of the overall style.
8.在使用云石膠打點之后，還要使用專用的AB膠固定，這樣才能確保穩定性。
8 after using the marble glue dot, but also the use of special adhesive fixed, so as to ensure the stability of.
9.電梯門套全部安裝完成后，即使進行現場清理工作，還有做好調色勾縫處理。還要注意對石材陽角的保護，用泡沫護角將它包裹起來。這樣能避免受到碰撞損壞。
9 elevator door all the installation is complete, even on-site clean-up work, and good color pointing processing. Should pay attention to the protection of Stone Yang angle, foam corner will wrap it up. This can avoid collision damage.
好了，小編今天就為大家簡單介紹到這里啦！明天的咨詢會更精彩哦！請大家不要錯過哦！
Well, Xiao Bian today for everyone to introduce here! Tomorrow's consultation will be more exciting oh! Please do not miss oh!
Explain the construction elevator door notices, the following small for you to explain:
1.在安裝電梯門套時，想要將各層需要的石材挑選好。根據尺寸、顏色和花紋來搭配，然后搬運到各個樓層需要使用的地方。
1 in the elevator door installation, to each layer of stone selection. According to size, color and pattern to match, and then transported to the floor where the need to use.
2.在安裝時要注意石材的紋理，盡量保持色澤一致，紋理連貫。安裝完成之后，電梯門套的美觀性才會最佳。
2 in the installation should pay attention to the texture of the stone, as far as possible to maintain consistent color, texture coherence. After the installation is complete, the appearance of the elevator door will be the best.
3.彈線的時候要仔細測量，不僅一個門套要做好垂直和平整性，每個門套之間也要注意這些問題。
When the 3 bomb line must be measured carefully, not only a door to do vertical integration of peace, we should pay attention to these problems between each.
4.在安裝側板和線條時，要保證至少有2個掛件作為支撐件。安裝角鋼的位置要測量精確，在中間增加一個加固點的點位。這樣做是為了讓門套石材更加穩定、牢固。
4 in the installation side and lines, to ensure that at least 2 pendant as support. The installation angle of the position to increase the measurement accuracy, a reinforcement point in the middle. This is done in order to make more stable and solid stone door.
5.安裝電梯門套時不要靠得太緊，在電梯門框邊預留5mm到8mm的位置，注意讓四周的預留位保持一致。
5 when the elevator installation door and don't get too tight in the elevator door post reserved for the 5mm to the 8mm position, pay attention to the surrounding the reservation is consistent.
6.在安裝電梯門的檻石時，地磚和電梯框邊要有3mm左右的坡度，門框邊和頂面石材外口要有2mm左右的斜度。
6 in the installation of the elevator door sill stone, floor tiles and lift frame edge is about 3mm to slope, and the top surface of the doorframe side stone mouth about 2mm slope.
7.頂面線條碰和側面線條的角度為45°，碰角做到嚴密、平整，施工時注意縫隙內不留余膠。如果有余膠就及時清理掉，然后使用勾縫劑處理。線條大小一致，造型穩合整體風格。
7 the top surface of the line and the side of the line angle of 45 degrees, the impact angle to be tight, smooth, pay attention to the construction of the gap does not leave any glue. If you have time to clean out the glue, and then use the pointing agent. The size of the same line, the shape of the overall style.
8.在使用云石膠打點之后，還要使用專用的AB膠固定，這樣才能確保穩定性。
8 after using the marble glue dot, but also the use of special adhesive fixed, so as to ensure the stability of.
9.電梯門套全部安裝完成后，即使進行現場清理工作，還有做好調色勾縫處理。還要注意對石材陽角的保護，用泡沫護角將它包裹起來。這樣能避免受到碰撞損壞。
9 elevator door all the installation is complete, even on-site clean-up work, and good color pointing processing. Should pay attention to the protection of Stone Yang angle, foam corner will wrap it up. This can avoid collision damage.
好了，小編今天就為大家簡單介紹到這里啦！明天的咨詢會更精彩哦！請大家不要錯過哦！
Well, Xiao Bian today for everyone to introduce here! Tomorrow's consultation will be more exciting oh! Please do not miss oh!
上一篇：仿大理石uv板可以照射嗎
下一篇：ktv門頭裝修新型材料有哪些
